Eugene Panel Upgrades
Hub City Electric LLC upgrades electrical panels for Eugene homes: 100-amp services brought up to 200, recalled Federal Pacific and Zinsco panels replaced, load calculated for a heat pump and an EV charger. Licensed Oregon electrician (CCB#247871), EWEB coordination handled, one price up front.
When a Eugene Panel Has to Come Out
A main panel is the heart of the electrical system, and across Eugene a lot of them are simply out of room and out of date. Homes through Friendly, Whiteaker, College Hill, and the older stretches near the University of Oregon are still running a 100-amp service that was plenty in its day. Today that same panel is asked to carry a heat pump, an EV charger, an electric range, a hot tub, and a house full of electronics. When demand outgrows the box, the signs show: breakers that trip when two big loads run together, no open slots to add a circuit, a panel that feels warm to the touch, or a home inspector flagging the service during a sale.
There is also a safety category all its own. If your Eugene home has a Federal Pacific Stab-Lok panel or a Zinsco panel, those are known fire and failure risks. The breakers can fail to trip on an overload, which defeats the one job a breaker exists to do. We replace them regularly across the valley, and we would rather you not wait for a problem to show itself. Whatever the reason your panel is on the list, we start by looking at the real load and telling you straight what the house needs, with no upsell.
100A to 200A Service Upgrades
The most common Eugene panel job. We increase your service capacity to 200 amps so the home can carry modern loads with room left to grow, and we handle the EWEB side of it.
Federal Pacific and Zinsco Replacement
Recalled and failure-prone panels swapped for a safe modern panel with properly rated breakers. Common in older Eugene housing stock and a smart move before a sale.
Load Calculations
Before we size anything we run a real load calc for your home’s appliances, HVAC, and any planned additions, so the new panel and service are right for how you actually use power.
Meter Base and Service Entrance
When the upgrade touches the meter base, mast, or service entrance conductors, we replace what needs replacing and bring the whole entrance up to current code, the box inside and the parts feeding it.
Subpanels and Circuit Room
Adding a shop, an ADU, or a garage full of dedicated circuits sometimes calls for a subpanel rather than a full service change. We tell you which one your project actually needs.
Grounding and Bonding
An older panel often has grounding and bonding that no longer meets code. We correct it as part of the upgrade so the new service is protected the way it should be.
How a Eugene Panel Upgrade Actually Goes
A service upgrade in Eugene is a coordinated job, not just a swap. The panel and service entrance sit between your home and the utility, and on an EWEB-served address that means the utility has to briefly disconnect and reconnect the power at the meter. We handle that coordination with EWEB, so you are not the one on hold arranging a disconnect while an open panel waits. We also pull the electrical permit through Lane County and the City of Eugene, do the work to Oregon code, and schedule the inspection. When the inspector signs off, the upgrade is on the record, which matters at resale and for insurance.
Most residential panel upgrades in Eugene are a full-day job. We plan the power-off window so it lands where it is least disruptive, get the old panel out and the new service in, and get you powered back up the same day in the large majority of cases. Eugene is a regular market for us at the south end of the valley, so scheduling the work and any follow-up stays straightforward. You will get a written price before the work starts, and there is no charge for the visit to quote it.
Planning an EV charger or a heat pump? Upgrade the panel first if it is full, and we will size the service for both at once. See our Eugene EV charger page.
Veterans get 5% off. Call (541) 220-0295.
What the Upgrade Looks Like Start to Finish
On-Site Look
Brandon comes to your Eugene home, reads the existing service, runs the load calc, and gives you a written price. No charge for the visit.
Permit and Utility
We pull the Lane County electrical permit and coordinate the power-off window with EWEB so the day is planned.
Panel Out, Service In
Old panel and any tired service-entrance parts come out, the new 200-amp service goes in, grounding and bonding corrected to code.
Inspection and Power
Power restored the same day in most cases, inspection scheduled, and the upgrade signed off and on the record.
Panel full, warm, or on the recall list?
Call or message us for a free quote on a Eugene panel upgrade. We handle the permit and the EWEB coordination.
Eugene Panel Upgrade Questions
How do I know if my Eugene home needs a panel upgrade?
Common signs: a 100-amp service when the home now runs a heat pump and an EV charger, a panel with no open slots to add a circuit, breakers that trip when two big loads run together, a panel that feels warm, or an inspector flagging the service during a sale. If you have a Federal Pacific or Zinsco panel, replace it regardless. Call (541) 220-0295 and we will come look at it at no charge.
Why are Federal Pacific and Zinsco panels a problem?
Both are known failure risks. The breakers can fail to trip on an overload or short, which defeats the whole purpose of a breaker and creates a real fire hazard. They are common in older Eugene housing, and we replace them regularly across the valley. If yours is one of these, we recommend swapping it for a safe modern panel.
Do you coordinate the power shutoff with EWEB?
Yes. A service upgrade means the utility has to briefly disconnect and reconnect power at the meter. On EWEB-served Eugene homes we handle that coordination so you are not arranging a disconnect yourself while an open panel sits in the garage. We plan the power-off window so it lands where it is least disruptive.
How long does a panel upgrade take in Eugene?
Most residential panel upgrades are a full-day job: pulling the permit, coordinating the EWEB shutoff, removing the old panel, installing the new 200-amp service, and scheduling the inspection. Power is back on the same day in the large majority of cases. We give you a realistic timeline when we come out to quote it.
Do I need a permit for a panel upgrade in Eugene?
Yes. Panel and service upgrades require an electrical permit through Lane County and the City of Eugene. We pull it, do the work to Oregon code, and schedule the inspection so the upgrade is signed off and on the record, which matters at resale and for insurance.
Can you size the panel for a future EV charger or heat pump?
Yes, and it is smart to. If you are planning an EV charger, a heat pump, a hot tub, or an ADU, tell us up front and we will run the load calc and size the 200-amp service so it carries current loads plus what you are adding, with room to spare. Doing it once is cheaper than upgrading twice.
