Commercial Wiring Services in Albany
Commercial wiring contractor in Albany, OR. Hub City Electric handles commercial new construction and retrofit wiring. CCB#247871. Call (541) 220-0295.
Commercial Wiring Done to Spec
Commercial wiring plays by tighter rules than residential. The voltages are higher, the code requirements are more involved, three-phase power enters the picture, and the tolerances on conduit and terminations are stricter. Hub City Electric provides commercial wiring for new construction and existing buildings in the Albany area, working from engineer-stamped plans or designing in the field depending on the project.
We handle the full range of commercial wiring, branch circuits, feeder conductors, three-phase equipment circuits, and the low-voltage that runs alongside power, data, voice, alarm, and control. A lot of commercial projects need the power and the low-voltage planned together, and we run both rather than leaving you to coordinate two trades. Whether it is a new building going up or new equipment going into an occupied space, the work is done to spec, documented, and ready for inspection.
Working in occupied commercial buildings is its own skill. You cannot shut the whole place down for a week, and the wiring has to go in around a business that is still running. We plan the access and the scheduling to minimize disruption, and we keep the areas we work in clean and safe because your staff and customers are still using the building. Small crew means clear communication on exactly when we need access to what, instead of surprises that throw off your operation.
Commercial New Construction Wiring
Branch circuit wiring for commercial new build projects.
Existing Building Wiring
Add circuits, update panels, and upgrade wiring in occupied commercial buildings.
Three-Phase Wiring
Three-phase service and equipment circuits for industrial and commercial use.
Low-Voltage Wiring
Data, voice, alarm, and control wiring alongside power work.
Conduit & Raceway Installation
EMT, rigid conduit, and cable tray installation for commercial applications.
The Commercial Wiring Services Process
Review plans or scope in the field
We work from engineer-stamped drawings or design on site, then tell you what the wiring’ll cost before we start.
Pull the commercial permit
All commercial electrical work needs a permit. We file it and coordinate inspections with the jurisdiction.
Run conduit, power, and low-voltage
We install raceway and conduit, pull branch and feeder conductors, and run data and control wiring alongside.
Terminate, test, and document
We land every termination to spec, test under load, and leave the work documented and inspection-ready.
What to Know Before You Start
Three-phase work is where commercial really separates from residential. Industrial equipment, large HVAC, and commercial machinery often run on three-phase power, and wiring it correctly, with the right conductors, conduit fill, and protection, takes experience residential work does not build. We handle three-phase service and equipment circuits, and we know the code requirements that come with them.
Conduit and raceway are the visible craftsmanship of a commercial job, EMT, rigid conduit, and cable tray run clean and supported the way the code and the inspector expect. Sloppy conduit is the first thing an inspector flags. Every commercial electrical project requires permits and inspection coordination, which we handle. Cost depends on the conductor and conduit runs involved, whether three-phase equipment is in play, and the access constraints in an occupied building. We give you the honest scope before the work starts.
On a commercial job the numbers matter before the wire ever goes in. Conductor sizing comes off a real load calculation, conduit fill has to stay inside what the code allows for the number of conductors in a run, and voltage drop on long runs has to be figured so equipment at the far end gets the voltage it actually needs. Getting those right on paper is what keeps an inspector from red-tagging the work and what keeps a motor or a piece of machinery from running hot for years. We do that math up front rather than guessing and oversizing everything, which keeps the material cost honest.
The coordination side is just as real. On a commercial project there is usually a GC or a property manager scheduling several trades through the same space, and the wiring has to slot in around the framers, the mechanical crew, and the data installers. We talk directly with whoever is running the schedule so everyone knows when we need access to a chase or a ceiling, and we get our material on site ahead of time so a backordered breaker or a missing length of cable tray never becomes the thing that holds up your project.
Licensed Oregon electrician (CCB#247871) covering Albany and a 70-mile radius across the Willamette Valley. Call (541) 220-0295 for a free quote with a clear price up front.
Veterans get 5% off. Mention it when you reach out.
Why Albany Calls Us for This Work
Three-phase done right
Industrial equipment and large HVAC run on three-phase. We wire it with the correct conductors, conduit fill, and protection.
Power and low-voltage in one trade
We run the data, alarm, and control wiring alongside the power, so you are not coordinating two separate crews.
We work around your operation
In an occupied building, we plan access and scheduling to keep your business running while the wiring goes in.
Inspection-ready conduit
Clean, supported EMT, rigid, and cable tray that passes the first time. Sloppy conduit is the first thing an inspector flags.
Licensed Electrician for Albany, OR
Hub City Electric LLC is licensed in Oregon (CCB#247871) and carries full insurance. Brandon founded the company in 2023 and brings 11 years of electrical experience. Every job is handled by our own crew. No subcontractors, no shortcuts.
Common Questions
What types of commercial wiring do you handle?
Branch circuit wiring, feeder conductors, three-phase equipment circuits, low-voltage control wiring, and data conduit. We work from plans or design in the field.
Do you work in occupied commercial buildings?
Yes, with proper planning to minimize disruption. We’ll discuss access needs and scheduling during our initial conversation.
Do you pull commercial permits?
Yes. All commercial electrical work requires permits. We handle the application and coordinate inspections.
Can you work from existing electrical plans?
Yes. We read blueprints and can work from engineer-stamped plans or rough sketches depending on the project scope.
Do veteran-owned businesses get a discount?
Yes, 5% off.
What’s your commercial service area?
Albany, Corvallis, Salem, Eugene, Lebanon, and surrounding communities within 70 miles.
Need your building wired right?
Call or message us for a free quote. We pick up fast and give you a straight answer.